ALARIS SERIES (ALARIS)
CartridgePleated
Key Features
- Retrofit-friendly for standard industrial housings
- Pleat pack resists channeling under pressure swings
- Low dP design for energy-efficient throughput
Overview
High-efficiency pleated cartridge with exceptional dirt holding capabilities
How It Works
Fluid flows outside-to-inside through layered depth-surface media; particles are retained within the matrix
Applications
- •RO pretreatment and SDI reduction
- •Well intake sand/silt removal
- •Chemical batch/transfer prefiltration (compatibility check)
- •Catalyst fines and solids removal
- •Coolant/cutting fluid fines control
- •Whitewater and coating kitchen filtration
- •Plant water and utility polishing
- •Boiler feed/condensate particulate protection
- •Cooling tower sidestream filtration
- •DI/RO rinse water prefiltration
- •CMP slurry trap
- •Marine potable/ballast water particulate control
FAQs
- •
What competitor cartridges does the ALARIS Series replace?
ALARIS is a direct replacement for Parker Poly-Mate/Poly-Mate Plus, Jonell LiquiPleat E/P/G, AJR PPO/PPOW, AMBF Pleated, and Graver PME/PMA/PMG cartridges.
- •
What efficiency options are available?
ALARIS is available in AS Series (90% nominal efficiency) and AG Series (99.98% absolute efficiency at Beta 1000) to match your application requirements.
- •
What end cap configurations are available?
ALARIS offers DOE, 222, 226, spring seal, and custom end cap options to fit standard industrial cartridge housings.
Physical Specifications
flow direction
Outside-to-inside
backwash-able
No
outside diameter options
2.5", 2.65", 2.75", 4.5"
inner diameter options
1.0"
nominal length options
9.75", 10", 19.5", 20", 29.25", 30", 39", 40"
surface area
4 ft² per 10-inch cartridge
end cap options
DOE W/ Gaskets, 222/Flat Single Open End, 222/Fin Single Open End, 226/Flat Single Open End, 226/Fin Single Open End, SOE W/ Plastic Spring & 222, SOE W/ Spring, 226 w/Spring, Direct Bond Gaskets, Custom
caps materials
Polypropylene
cores materials
Polypropylene, Polyester, Carbon Steel, Stainless 304, Stainless 316
gasket material options
Buna-N, EPDM, Silicone, Viton, Teflon encap. Viton, Neoprene
Media Specifications
media primary options
Polypropylene, Polyester, Fiberglass
micron ratings
0.2, 0.5, 1, 3, 5, 10, 25, 50
efficiency percent
Up to 99.98%
media rating
Absolute, Nominal
beta ratio
Up to 1000
changeout dp
15 PSID
burst pressure
35 PSID
max temperature
180°F (Polypropylene, Polyester), 250°F (Fiberglass)
approvals certifications
FDA Listed
Housing Compatibility
Competitor Cross-Reference
- Parker Fulflo Poly-Mate
- Parker Fulflo Poly-Mate Plus
- Jonell LiquiPleat E (JPME)
- Jonell LiquiPleat P (JPMP)
- Jonell LiquiPleat G (JPMG)
- AJR PPO
- AJR PPOW
- AMBF High Efficiency Pleated Cartridges
- AMBF Standard Efficiency Pleated Cartridges
- Graver PME
- Graver PMA
- Graver PMG
Build Your Model Code
Your Model Code(0/8 required)
___-___-___-___-___-___-___-___Example:
AS-PO-5-D1-40-PO-E2-BN-R